 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MIC8115 Micrel MIC8115 Microprocessor Reset Circuit General Description The MIC8115 is an inexpensive microprocessor supervisory circuit that monitors power supplies in microprocessor based systems. The function of this device is to assert a reset if the power supply drops below a designated reset threshold level or /MR is forced low. The MIC8115 has an active low /RESET output. The reset output is guaranteed to remain asserted for a minimum of 1100ms after VCC has risen above the designated reset threshold level. The MIC8115 comes in a 4-pin SOT-143 package. Features * * * * * * * * * * * * Precision voltage monitor for 3.3V power supplies Specifically tailored to the AMD Elan SC500 Series /RESET remains valid with VCC as low as 1V 5A typical supply current 1100ms minimum reset pulse width Manual reset input Available in 4-Pin SOT-143 Package Portable equipment Intelligent instruments Critical microprocessor power monitoring Printers/computers Embedded controllers Applications Ordering Information Part Number MIC8115TU MIC8115TUY Marking NT NT Operating Temp. Range -40C to +85C -40C to +85C Package 4-lead SOT-143 4-lead SOT-143 Pb-Free No Yes Typical Application VCC VCC VCC MIC8115 MR P RESET RESET MIC8115 Typical Application Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com July 2005 1 MIC8115 MIC8115 Micrel Pin Configuration GND 1 4 VCC MIC8115 RESET 2 3 MR 4-Lead SOT-143 Pin Description Pin Number 1 2 Pin Name GND /RESET Pin Function IC Ground Pin /RESET goes low if either VCC falls below the supply reset threshold voltage or if /MR is asserted. /RESET remains asserted for one reset timeout period 1100ms min. After both VCC exceeds the supply reset threshold voltage and /MR is deasserted. Manual Reset Input. A logic low on /MR forces a reset. The reset will remain asserted as long as /MR is held low and for one reset timeout period (1100ms min.) after /MR goes high. This input can be shorted to ground via a switch or driven from CMOS or TTL logic. Pulled high internally through a 20k resistor. Float if unused. Power supply Input. 3 /MR 4 VCC MIC8115 2 July 2005 MIC8115 Micrel Absolute Maximum Ratings(Note 1) Terminal Voltage (VCC) ...........................................................-0.3V to 6.0V (/MR) ..................................................-0.3V (VCC + 0.3V) Input Current (VCC, /MR) ............................................ 20mA Output Current (/RESET) ........................................... 20mA Rate of Rise (VCC) ..................................................100V/S Lead Temperature (soldering, 10 sec.) ...................... 300C Storage Temperature (TS) ........................ -65C to +150C ESD Rating .................................................................... 3kV Operating Ratings(Note 2) Operating Temperature Range MIC8115TU ............................................ -40C to +85C Power Dissipation (TA = +70C) .............................. 320mW Electrical Characteristics For typical values, VCC = 3.3V; TA = 25C, bold values indicate -40C TA +85C; unless noted Symbol VCC ICC VTH Parameter Condition Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period /RESET Output Voltage /RESET Output Voltage /MR Minimum Pulse Width /MR to Reset Delay /MR Input Threshold, VIH /MR Input Threshold, VIL /MR Pull-Up Resistance /MR Glitch Immunity Note 1. Note 2. Note 3. Exceeding the absolute maximum rating may damage the device. The device is not guaranteed to function outside its operating rating. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. Min 1 Typ 5 Max 5.5 15 3.15 2500 0.3 0.3 Units V A V ms V V V s s V TA = -40C to 85C 3.00 1100 ISOURCE = 500A VCC = VTH min, ISINK = 1.2mA 0.8xVCC 3.08 1700 tRST VOH VOL VCC = 1V, ISINK = 50A, TA = -40C to +85C 10 0.5 0.7xVCC 10 20 100 0.25xVCC 30 k ns Timing Diagram VCC /MR VTH /RESET tRST tRST July 2005 3 MIC8115 MIC8115 Micrel Functional Diagram VCC MR (3) RESET GENERATOR RESET (2) VCC (4) + Reset Threshold (V) - GND (1) MIC8115 4 July 2005 MIC8115 Micrel /RESET Valid at Low Voltage A resistor can be added from the /RESET pin-to-the ground to ensure the /RESET output remains low with VCC down to 0V. A 100k resistor connected from /RESET-to-ground is recommended. The resistor should be large enough not to load the /RESET output and small enough to pull-down any stray leakage currents. VCC Applications Information Microprocessor Reset The /RESET pin is asserted whenever VCC falls below the reset threshold voltage. The reset pin remains asserted for a period of 1100ms after VCC has risen above the reset threshold voltage. The reset function ensures the microprocessor is properly reset and powers up into a known condition after a power failure. /RESET will remain valid with VCC as low as 1V. VCC Transients The MIC8115 is relatively immune to the negative-going VCC glitches below the reset threshold. Typically, a negative-going transient 125mV below the reset threshold with a duration of 20s or less will not cause a reset. VCC VCC MIC81 15 RESET 100K P RESET /RESET Valid to VCC = 0V July 2005 5 MIC8115 MIC8115 Micrel Package Information 0.950 (0.0374) TYP 1.40 (0.055) 2.50 (0.098) 1.20 (0.047) 2.10 (0.083) C L C L DIMENSIONS: MM (INCH) 1.12 (0.044) 0.81 (0.032) 8 0 0.150 (0.0059) 0.089 (0.0035) 3.05 (0.120) 2.67 (0.105) 0.800 (0.031) TYP 0.400 (0.016) TYP 3 PLACES 0.10 (0.004) 0.013 (0.0005) 0.41 (0.016) 0.13 (0.005) 4-Lead SOT-143 (UT) TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated. MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA MIC8115 6 July 2005 |
Price & Availability of MIC811505
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |